Join the waitlistJoin
Life Lever Moto

What do you want lifelever to help with?

Not sure? Start with your own AISee all levers

More coming: finance, work, parenting.

Moto

KTM 300 XC-W TBI (2024 to 2026)

What the throttle-body-injected 2-stroke 300 says on its diagnostic plug, what we can read from it, and what it keeps to itself.

For the curious: you do not need any of this to ride.

The short version: the 2024 and later KTM 300 XC-W with throttle body injection speaks the standard diagnostic channel for fault codes and the VIN, and says nothing for live data. The live data is there anyway. The engine computer broadcasts it on the CAN bus many times a second, and we listen and decode it. Everything below was read from a real 2025 bike with a Bluetooth LE data connector, and a 2026 bike answered the same way on a 2.5 hour ride.

Back to all bikes.

At a glance

Item What we found Status
Bike KTM 300 XC-W TBI, model years 2024, 2025 and 2026 in the profile 2025 and 2026 verified
ECU Vitesco (formerly Continental) M4C Part number read over UDS
Plug KTM 6-pin, the clear/white one Verified by photo
Bus CAN, 11-bit ids, 500 kbit/s Verified
Ids Request 0x7E0 (one ECU) or 0x7DF (everyone), answer from 0x7E8 Verified
Standard live data (mode 01) Empty Verified
Fault codes Stored (mode 03) and pending (mode 07) work Verified
VIN Mode 09 and UDS both give it Verified
Clearing codes Not tried on this bike Untested
Power The plug is only live while the engine runs Verified

The plug

The bike has a 6-pin KTM diagnostic connector with a cap on it. There are two kinds of KTM 6-pin and they do not fit each other. The older one is clear or white; the Euro 5 one (ISO 19689) is red. Our 2025 bike has the clear one, so it takes a 6-pin to 16-pin diagnostic cable of the kind sold as “K-line plus CAN”. A basic one worked. If you shop for one, note that this bike needs both CAN wires, so a K-line-only cable will not do, and KTM’s own dealer cable is not a standard diagnostic cable at all.

The pinout of the clear 6-pin comes from owner forums and cable makers, not from a KTM document:

KTM pin Signal 16-pin equivalent
1 Battery +12 V 16
2 CAN high 6
3 CAN low 14
4 K-line (no wire on the 2-strokes) 7
5 Wake input none
6 Ground 4 and 5

The plug sits under the seat near the ECU, and on some bikes in the airbox. Do not confuse it with the 2-pin connector near the ECU, which is a CAN termination resistor.

Power: the engine has to be running

The diagnostic socket is fed through a relay that drops a few seconds after the engine stops. With the key on and the engine off the data connector loses the bus, so every read starts with a running engine. We saw 14.4 V at the data connector with the engine running. A side effect is good news: the data connector cannot flatten the bike’s battery by sitting in the plug, because the socket is dead when the engine is off.

What the standard channel answers

All of this is on the physical request id 0x7E0 and answers from 0x7E8.

Question Answer
Mode 01, PID 00 (which live values do you have?) Replies, with an empty list
Mode 01, PID 01 (check engine lamp) and PID 20 No data
Mode 03 (stored codes) Works. One code was stored on 2026-10-19 (see below)
Mode 07 (pending codes) Works. None pending
Mode 09 (identification) Works. Advertises six items: 02 (VIN), 04 (calibration id), 06, 08, 0A (ECU name) and 15
UDS 0x22 (read identifier), default session Works. Same VIN, plus the identification block below
Mode 04 (clear), mode 0A, extended UDS sessions, anything that writes Not tried

The ECU names itself ECM-EngineControl. We swept the standard identification range 0xF180 to 0xF19A and the ECU answered 16 identifiers and refused 112 as out of range, in 30 seconds. The answers include the ECU part number, software number, hardware number, manufacturing date, programming date, serial number and the VIN. We do not publish the VIN or the serials. The ECU part number matched what research had suggested for the M4C.

One quirk worth knowing: if you ask a mode 09 question to the functional id 0x7DF, the second frame of a long answer can come back corrupted. Asking 0x7E0 directly is correct, and Life Lever Moto does that.

The VIN also tells the app which bike it is looking at. The maker code says KTM, the model code says 300 XC-W, and the app names it “2025 KTM 300 XC-W”.

Live data: listening to the broadcast

The bus carries five message ids and nothing else. We captured 20 seconds idle and 20 seconds with throttle blips, 2,821 frames each, with no errors:

Id Rate What it is
0x6DA 20 Hz Engine speed, throttle, and more
0x6DB 20 Hz Coolant, power valve, and more
0x6AB 1 Hz Two constant, alternating payloads, one of them unique to each bike
0x4C0 50 Hz Constant
0x4C1 50 Hz Constant

Because we only listen, nothing here asks the ECU to do anything, and we never try seed-and-key security access. Reading what a bus broadcasts of its own accord circumvents nothing.

What we decode

Item Where Unit Rate Status
Engine speed 0x6DA, bytes 0 and 1, big-endian, raw times 0.25 rpm Frames at 20 Hz, shown up to 10 Hz Verified
Power valve position 0x6DB, byte 1 Raw position between the valve’s learned stops, not a percentage Up to 10 Hz Verified
Throttle, raw 0x6DA, byte 2 Raw count: closed 40, wide open 294 Up to 10 Hz Decoded
Throttle, percent Same byte, (raw minus 40) divided by 254, times 100 Percent Up to 10 Hz Decoded
Coolant temperature 0x6DB, byte 0, no offset Degrees C, shown in F in the app 1 Hz Decoded

How we know each one:

  • Engine speed is verified against sound. A single-cylinder 2-stroke fires once every revolution, so the firing rate in the exhaust note is the rpm. The recording matched the decode to within a few percent. Idle ran 1,470 to 2,230 rpm (uneven, as a 2-stroke is), and blips on 2026-10-19 and 2026-10-20 reached 8,829 rpm.
  • Power valve is driven by rpm, not throttle. It reads 1 below 5,000 rpm, 17 to 31 at 5,200 to 5,500, 50 at 6,000, 85 to 100 at 6,500 to 6,700, 120 to 130 at 7,200, 149 at 7,800 and 201 on an 8,100 rpm blip. At a held 6,400 rpm it read the same with the throttle nearly wide open and nearly closed. The repair manual calls it the exhaust control actuator.
  • Throttle is read from byte 2. The byte sits at exactly 40 with the throttle closed, and it counts past 255 at wide open, so it wraps. We found that on the first ride day: wide open is 294, which shows as 38 once it wraps. The app reads any value below 40 as 256 more.
  • Coolant is read from byte 0. A cold start from 24 to 26 C read 47 at 70 seconds after power-on, climbed a degree every 4 to 10 seconds, and plateaued at 106 C (223 F) at idle, settling to 100 or 101 with the radiator fan on.

Seen in the frames

These came out of analysing the first ride captures.

Where What it is Evidence
0x6DA, bytes 6 and 7 Barometric pressure in hPa Reads 910 to 956 hPa, moves against GPS altitude with a correlation of minus 0.99
0x6DB, bytes 3 and 4 An ignition advance map Raw values
0x6DB, byte 6, low nibble An engine-hours counter Steps up by 2 every 45 to 60 minutes of running
0x6DB, byte 7 A second temperature Raw values

There is no injection time or fuel quantity in the broadcast, and no manifold pressure.

Fault codes

Codes come from mode 03 (stored) and mode 07 (pending), decoded on the standard diagnostic channel over CAN. The one real code we have read is P0107, a stored manifold absolute or barometric pressure circuit low input. It was read on 2026-10-19 and has not been cleared.

The KTM also reports codes as blink counts on the check engine lamp, and owner guides list some. Those are forum samples, not a catalog.

The check engine lamp state is not read: mode 01 PID 01 gives no data, and no bit in the broadcast follows the lamp. The app reads codes in the background every 10 minutes, with live data first, so it shows how many codes are active. Clearing is off for this bike.

Battery and charging

The data connector reads the voltage at the plug, a few tenths under the battery terminals. With the engine running we saw 14.4 V on the bench, and on the first ride day 44 readings between 13.2 and 14.6 V on one bike and 553 readings between 13.6 and 14.5 V on the other.

KTM lists a lithium battery for the TBI models. Battery watch flags use lead-acid numbers until you say which battery you have.

What is not readable

  • Gear. The XC-W has no gear sensor. We looked for it indirectly: rpm against speed forms two clean bands one gear apart (a ratio step of 1.19 to 1.21), but 72 to 77 percent of moving samples fall outside them, and at 10 to 25 mph no band forms. Neither rear wheel speed nor clutch state is in the captured data.
  • Wheel speed and clutch. Same finding. Speed comes from the phone’s GPS.
  • Check engine lamp state. See above.
  • Injector timing, oil pump duty, map switch choice. Not in the broadcast.

First ride day, 2026-10-25

Two KTM 300 XC-W bikes, a 2025 and a 2026, each with its own Bluetooth data connector and its own iPhone, rode for 2.5 hours. Counts, per bike:

2025 bike 2026 bike
Distance 21 miles 21 miles
GPS points 9,011 9,090
Data connector connections 37 29
Engine running 3,875 s (65 min) 5,416 s (90 min)

The 2026 bike was switched to the same profile and read the same values as the 2025 bike, and the numbers looked right to us on the bike, so 2026 was added to the profile.

The ride also found a problem. On one phone the engine data stopped for 16 minutes until the bike was restarted. That led to a fix in the app: it now tries to recover on its own, and then tells the rider to power-cycle the bike or data connector. Stops of the engine and lost links inside a ride show up as gaps in the engine data, never as the end of the ride.

Later analysis of those captures is where the throttle wrap, the barometric pressure field and the gear findings above came from. See GPX in and out for how the ride itself is recorded and Lean and g for lean and g.

What it is not

The Moto app does not flash or tune the bike, and it does not write maps. It reads.

KTM and Triumph are trademarks of their owners; lifelever is not affiliated with them.

Ride with Moto

Your ride and your bike, in one app.

Moto is in private beta, free while it lasts, then $5.99 a month with every lifelever app included. Beta riders get the exact tested parts list with their invite.

Join the waitlist